Draper Expert Plasma Cutter, 25A

Clean, precise and capable, the Draper Expert IPC25 25A Plasma Cutter is a professional-grade cutting tool built for workshop and fabrication use. Equipped with IGBT inverter technology for stable, efficient arc performance, it cuts through stainless steel, aluminium and other electrically conductive metals up to 8mm thick — delivering smooth, accurate cuts with minimal heat distortion.

Designed with practicality in mind, the IPC25 integrates both a gas regulator and a water trap directly into the machine — reducing the need for separate ancillary equipment and keeping the setup clean and compact. Thermal overload protection safeguards the machine during sustained use, while the lightweight, robust chassis and carry handle make it easy to move around a workshop or take to site.

Fitted with a 13A plug as standard, the IPC25 is ready to connect and cut from a standard domestic or workshop supply.

Key Features

IGBT Inverter Technology

Insulated Gate Bipolar Transistor (IGBT) inverter technology is the industry standard for modern plasma cutters and welding equipment. It produces a stable, smooth arc with consistent cutting performance, greater energy efficiency and a more compact power unit compared to older transformer-based designs. The result is cleaner cuts, reduced operating costs and a machine that's significantly lighter and more portable.

Cuts Up to 8mm — Stainless Steel, Aluminium and Conductive Metals

The IPC25 is rated for cutting any electrically conductive material up to 8mm thickness, including stainless steel and aluminium — two of the most common fabrication metals and among the more challenging to cut cleanly with other methods. Plasma cutting produces a narrow kerf, minimal heat-affected zone and clean edges with little post-processing required.

Integrated Gas Regulator

The built-in gas regulator is integrated directly into the machine body, eliminating the need for a separate external regulator. This simplifies setup, reduces clutter in the workspace and ensures a consistent, controlled gas pressure to the torch throughout operation.

Built-In Water Trap

The integrated water trap filters moisture from the compressed air supply before it reaches the torch — moisture in the air supply is a common cause of arc instability and inconsistent cut quality. Having this built into the machine means one less piece of separate ancillary equipment and consistent protection for every cut.

Thermal Overload Protection

Thermal overload protection monitors the machine's operating temperature and cuts power if it exceeds safe limits — protecting internal components from heat damage during extended or heavy use. This safeguard helps maximise the machine's working life and prevents unexpected downtime from thermal shutdown.

Robust, Lightweight and Portable

The IPC25 is built to the standards of Draper's Expert range — robust enough for demanding professional use, yet lightweight and compact enough to carry between locations with ease. The integrated carry handle makes it genuinely portable, whether moving around a fabrication workshop or transporting to a site.

13A Plug Fitted — Ready to Use

Supplied with a 13A plug fitted as standard, the IPC25 connects directly to a standard workshop or domestic supply without any additional wiring or adaptation.

Specification

What Can a Plasma Cutter Do?

Plasma cutting uses a high-velocity jet of ionised gas (plasma) to cut through electrically conductive materials with speed and precision. Compared to angle grinders, cutting discs or oxy-fuel cutting, plasma cutting offers several practical advantages:

• Cleaner cuts — Narrower kerf and less spatter than flame cutting, with smoother edges
• Less heat distortion — The concentrated arc minimises heat spread to surrounding material
• Faster on thin material — Significantly quicker than oxy-fuel on metals under 10mm
• Versatility — Cuts steel, stainless steel, aluminium, copper, brass and other conductive metals
• No gas preheating — Ready to cut immediately, unlike oxy-fuel which requires preheat

For fabricators, metalworkers, vehicle restorers and general workshop use, a plasma cutter is one of the most versatile and efficient cutting tools available.

Who Is the IPC25 For?

The IPC25's 25A output and 8mm cut capacity make it well suited to:

• Fabricators and metalworkers handling sheet steel, stainless, and aluminium in a workshop environment
• Vehicle restorers cutting body panels, chassis sections and structural metalwork
• General workshop and garage use where a versatile, clean-cutting metal cutter is needed
• Jobsite use where a lightweight, portable machine with standard plug connection is required
• Hobbyist and enthusiast metalworkers stepping up from angle grinder cutting to professional plasma results

For materials above 8mm, a higher-amperage plasma cutter would be the more appropriate choice.

Why Choose the Draper Expert IPC25?

Draper's Expert range is the premium tier of Draper's product lineup — built to higher specifications and intended for professional and demanding regular use. The IPC25 reflects that: IGBT inverter technology, an integrated regulator and water trap, and thermal protection are features that matter in a machine used day after day in a working environment.

The integrated gas regulator and water trap in particular are worth noting. Many entry-level plasma cutters omit these or require external equivalents — the IPC25 includes both as standard, simplifying setup and ensuring cut quality is consistently protected from moisture-related arc instability.

Frequently Asked Questions

What gas does the IPC25 use? Plasma cutters typically use compressed air as the plasma gas, supplied by an air compressor. Check the product documentation for the required air pressure and flow rate specifications before use.

What thickness can the IPC25 cut? The IPC25 is rated for cutting electrically conductive metals up to 8mm thick, including stainless steel and aluminium.

Does it need a separate gas regulator? No — the gas regulator is integrated directly into the machine, removing the need for a separate external regulator.

What is the duty cycle of the IPC25? Duty cycle figures are not specified in the available product data. For confirmed duty cycle information, refer to the product manual or contact Draper directly.

What materials can it cut? The IPC25 cuts any electrically conductive material — including mild steel, stainless steel, aluminium, copper and brass. It cannot cut non-conductive materials such as wood, plastic or glass.

Is it suitable for a standard 13A socket? Yes — the IPC25 is supplied with a 13A plug fitted and connects to a standard domestic or workshop socket.